Maintenance

How To Flush A Water Heater: What The Manuals Say

A shared drain-and-flush sequence from two manufacturers, the intervals each source gives (they differ), the hazards, and the signs that a flush should be a professional job.

By Lancaster Water Heater Pros · Family-owned in Lancaster since 2018 · Updated

Flushing a storage water heater means draining the tank through its drain valve to clear sediment, and the manufacturer documents describe a similar order of steps but no single interval for every heater. Rheem, Bradford White and State Water Heaters each word the sequence a little differently, and the federal and EPA guidance gives intervals that are not the same task or the same schedule. This page sets out what each source says, where they differ and which problems should stop you. It covers storage tank heaters only; tankless units are descaled, not flushed, and have their own guide.

Safety first. The water in the tank and in the relief valve line can be hot enough to scald, and an electric or gas heater can shock, burn or leak gas if power or fuel is left on. Turn off the power or gas as the manual directs before anything else. If you smell gas, leave the building and use our shut-off guide. This page is a summary of what manuals say, not a replacement for the manual for your exact model.

What Flushing Is, And What It Is Not

In the documents we read, flushing is draining the tank completely through the drain valve so that settled sediment leaves with the water. Bradford White’s For The Pro page says the tank acts as a water filter, that contaminants in the incoming water settle in it, and that for this reason a water heater should be periodically flushed out through the drain valve. The State Water Heaters electric manual says periodic draining and cleaning of sediment from the tank may be necessary. Rheem’s article describes sediment as minerals that separate and settle at the bottom of the tank, and says a thickening layer reduces efficiency and increases wear on the system.

Flushing is a separate task from three jobs that sometimes get bundled with it. Operating the temperature-pressure relief valve is its own check; the State manual says the valve must be manually operated at least once a year and warns that the discharged water may be extremely hot, and our relief valve guide covers a valve that leaks. The anode rod has its own page, here. And a flush does not cure a leaking tank; see leaking from the bottom.

How Frequently: The Sources Differ, And None Fits Every Heater

No interval is stated by every source, and the figures that exist describe different tasks. The table records each statement with its scope. We do not combine them into one recommendation.

What each source says about the interval, in its own scope. These are not interchangeable.
SourceWhat it saysScope
Rheem, How Often To Flush Your Water Heater (May 29, 2026)Rheem says to flush once a year for most households, every 6 months for households with hard water, and more often if there is visible sediment or heavy use.A general consumer article from the manufacturer, not a model manual.
State Water Heaters, residential electric manualThe manual says periodic draining and cleaning of sediment from the tank may be necessary. It gives no interval in that section.That product family.
Bradford White, Draining a Water HeaterThe page quotes an industry trade association (AHRI) on flushing the tank each time you check the pressure relief valve, and tells readers to refer to the maintenance section of the installation and operation manual. It gives no calendar interval.A contractor-facing page; the manual for your model governs.
U.S. EPA, Legionella in the Indoor EnvironmentThe EPA says many manufacturers recommend flushing a water heater once a year, before you move into a home, after plumbing work and if the water is discolored, and says to follow the manufacturer’s instructions or have a professional do the work.The EPA reports what manufacturers recommend; it sets no interval of its own.
Federal Energy Saver, Storage Water Heaters (archived April 10, 2026)The archived page lists flushing a quart of water from the storage tank every three months among routine maintenance that may apply depending on the type and model, and tells readers to read the owner’s manual for specific recommendations.A small test draw, not a full flush; archived, not current guidance.

Rheem’s hard-water figure is Rheem’s statement about households that have hard water. This page does not say whether your water is hard; see how to find out. We state no flush interval of our own and found no source that supports one for every heater.

Before You Start: Decide Whether This Is A DIY Job

Read the manual for your model first; Bradford White’s page opens by pointing to the maintenance section of the installation and operation manual. Then check whether anything on this list applies; Rheem says to consider a professional in these cases, and we agree they are reasons to stop.

  • The drain valve will not open, or it leaks. Rheem lists this as a reason to call a professional.
  • There is heavy rust or corrosion around fittings, or noise continues even after flushing, per Rheem.
  • The unit is 8–12 years old or older, or has not been flushed in a while. Rheem says older systems or tanks that have not been flushed in a while may have hardened sediment that is difficult to remove without specialized tools, and that flushing such units yourself could lead to leaks or further damage.
  • You are unsure about the gas or electrical parts. Rheem lists this too, and Bradford White says that although there may be maintenance checks you can do yourself, it highly recommends a plumbing professional help.
  • You do not know where the water will go. The hose has to end at a drain or outdoors; see water heaters with no floor drain.
  • The unit has been under water or shows signs of flood damage. That is a replacement and inspection question, not a flush; see our flood damage guide.

The Common Sequence In The Manufacturer Documents

Rheem’s article and Bradford White’s For The Pro page describe the same order, and State’s electric manual gives a shorter drain-only version. The steps below are what those documents say, in the order they say it. They are not a procedure for your heater.

Scope of these steps. The steps below combine three documents of different kinds: a State Water Heaters manual for its electric storage heaters, a Bradford White page written for contractors, and a Rheem consumer article. Each step names the sources that say it; where a step names only some of them, the others did not say it in what we read. We did not read a gas storage heater manual for this page, so the valve layout and the gas and relief valve steps for your model must come from your own manual. The intervals on this page are attributed statements, not a schedule.

  1. Turn off the power or gas first. Rheem says to turn off the electricity, gas and cold water inlet. Bradford White says to turn off the electricity or turn the gas switch to pilot. State says to turn the electric power supply off before beginning.
  2. Close the cold water inlet to the heater.
  3. Let air in. State says to open a nearby hot water faucet; Rheem and Bradford White say to open the pressure relief valve.
  4. Connect a hose to the drain valve and send the water somewhere safe. State says to end the hose at an adequate drain or outdoors; Bradford White says to put the end where scalding hot water will not do harm.
  5. Open the drain valve and let the tank empty completely. Bradford White says draining completely ensures you have removed all possible sediment.
  6. Close the drain valve and disconnect the hose, then close the pressure relief valve if you opened it.
  7. Refill with the hot faucets open. Bradford White says to open all the hot water faucets in the house, turn on the cold water inlet and close each hot faucet as water begins to flow from it.
  8. Restore power or gas only after water is flowing. Rheem and Bradford White both put power and gas last; State says to follow its filling instructions, which include running a hot faucet until a constant flow is obtained, before turning the power on.

In the Rheem and Bradford White pages we read, neither describes briefly reopening the cold supply to stir the sediment during the drain; some other websites do, and we cannot attribute that step to either manufacturer.

Not sure your heater is a good DIY flush? Call (717) 500-8528 with the make and model from the rating plate.

Where The Documents Differ

Differences in wording between the three documents. Your own manual overrides this table.
StepState (electric manual)Bradford White (For The Pro)Rheem (article)
Power or gasElectric power offElectricity off, or gas switch to pilotElectricity, gas and cold water inlet off
Air inOpen a nearby hot faucetOpen the pressure relief valveOpen the pressure relief valve
Where the hose endsAn adequate drain or outdoorsWhere scalding hot water will not harmA container or area that will not be damaged by hot water
RefillFollow the filling instructions, then power onAll hot faucets open, then close each as it flows, then power on or gas switch to runAll spigots on, then each off once water flows, then electricity and gas on

If Something Goes Wrong

  • The valve will not open or will not stop leaking. Stop and call a professional, per Rheem. Stop rather than forcing it.
  • The pressure relief valve will not reset after you operate it. The State manual says to close the cold water inlet immediately, follow the draining instructions and replace the valve.
  • The water was discolored or cloudy before you started. Bradford White says a great majority of so-called rusty water conditions are sand and clay sediment, for example from well systems or water main repairs, and lists several possible causes of milky water, including air introduced at faucet aerators, with draining and flushing as a possible remedy. That is Bradford White’s description, not a diagnosis for your home.
  • Noise continues after the flush. Rheem lists this as a sign to call a professional; see also popping and rumbling noises.
  • The heater was off for a long time before you refill it. The State manual warns that hydrogen gas can build up in a hot water system that has not been used for a long period, and says to open the hot faucet at the kitchen sink for several minutes before electrical appliances are used, with no smoking or open flame near the faucet.

What A Flush Will Not Settle

A flush clears sediment from the tank; it does not repair a tank that is leaking, a valve that is failing or a unit that has reached the end of its life. The State manual says water heaters eventually leak and asks that installation be arranged so that a leak will not damage the structure. If you are weighing a repair against a new unit, see repair or replace and our guide to finding your heater’s age. We state no price for a flush; the repair cost guide carries only labelled national ranges.

Flushing And Legionella

The EPA says regular flushing of sediments from hot water tanks may also help control and prevent Legionella growth. It says to follow the manufacturer’s instructions or have a professional do the work. The CDC’s page for vacation rental owners says to routinely flush the water heater according to manufacturer recommendations. Both statements point back to the manual; neither gives a schedule. For the temperature side of that question, see our temperature setting guide.

Tankless And Heat Pump Units

Rheem’s article says tankless heaters require periodic descaling instead of flushing. See tankless descaling: what manufacturers say. Heat pump units have their own manuals, and this page does not cover them.

Sources Used

Rheem, How Often To Flush Your Water Heater (And How To Do It) (May 29, 2026); Bradford White For The Pro, Draining a Water Heater; State Water Heaters residential electric manual; U.S. EPA, Legionella in the Indoor Environment; CDC, vacation rental owners and managers; U.S. Department of Energy, Storage Water Heaters (archived capture, April 10, 2026, used for what it said, not for current rules). Details and excerpts are in our claims registry.

Need A Water Heater Flushed Or Checked?

Service requests and emergency service are available 24/7 across Lancaster City and Lancaster County.

Call For Emergency Service

Flushing A Water Heater FAQ

Why do you flush a water heater?

The manufacturers say sediment settles in the tank. Bradford White says the tank acts as a water filter, State says periodic draining and cleaning of sediment may be necessary, and Rheem says a thickening sediment layer reduces efficiency and increases wear. None of them gives a figure for how much, and we state none.

How often should a water heater be flushed?

It depends on the source and the model, and no one interval fits every heater. Rheem says once a year for most households and every 6 months for households with hard water; the EPA reports that many manufacturers recommend once a year; State and Bradford White refer you to the manual. Read the one for your unit.

Can I flush my water heater myself?

Rheem says it can be manageable, and also lists reasons to call a professional. Those include a drain valve that will not open or leaks, heavy rust or corrosion around fittings, noise after flushing, a unit that is 8–12 years old or older, and uncertainty about the gas or electrical parts. Bradford White highly recommends a plumbing professional help.

What is the difference between draining and flushing a water heater?

The manufacturer documents we read use the terms together. State describes draining the tank; Bradford White and Rheem describe draining it completely to flush out sediment. Other websites use “flush” for extra steps, and we cannot attribute those steps to a manufacturer.

Should I flush a water heater that has never been flushed?

Rheem says to be careful. It says older systems or tanks that have not been flushed in a while may have hardened sediment that is difficult to remove without specialized tools, and that flushing such a unit yourself could lead to leaks or further damage. If yours is in that position, ask a professional first.

Who can flush a water heater near me in Lancaster County?

Lancaster Water Heater Pros services water heaters across Lancaster City and Lancaster County. Call (717) 500-8528 with the make and model. Service requests are accepted 24/7.

Call (717) 500-8528